MegaLite Axis Manual do Utilizador descarregar pdf (Página 9)

17 16

17,7 cm

4 %

2 %

Sloping in

installation direction

Water draining

for drainage system

Max. 65 cm

Max. 50 cm

Ventilation

from below

Keep the minimum distance of

4 cm to upright, ﬁ xed components.

CLOSED DECK

Hint:

Do not use WAVE barefoot boards for

installation as closed deck.

FIX STEP SYSTEM

4 cm

distance from

edge plate DUO

to ﬁ xed

components

Max. 50 cm

distance between

the axes of all

plates in installation

direction of the

boards

Floor plan substructure

Distance between all

plates in installation

direction

max. 65 cm

Set connection clip crosswise in the

centre between plates

Hint:

The FIX STEP system does not

create the sloping of the terrace.

Attention:

Since the FIX STEP connection clips are

only used to secure the boards in vertical

position, they must be fixed to the

construction planks in every third row of

boards after inserting the groove strip by

means of the supplied screws.

Preliminary work

1. Prepare base grade exceeding the

planned terrace surface by 50 cm on all

sides with a sloping of 4 % and install

drainage in the ground.

2. Make a stable gravel or ballast bed

(frost-safe) with 2 % sloping. Then cover with

fine gravel to level uneven spots.

Sub-structure

3. To begin, click the FIX STEP mounts at

the same height level into all FIX STEP

plates. Then click the FIX STEP comfort

pads with the matching attachment piece

into them. Then stick a piece of retaining

band onto the centre of the attachment pie-

ces.

→ Cf. page 13

4. Place the FIX STEP edge plates DUO

at a distance of 4 cm parallel to upright

components and at an axis distance of max.

65 cm. Distribute FIX STEP plates parallel

to these at an axis distance of 50 cm. At the

end of the terrace, place FIX STEP edge

plates DUO again.

→ Cf. floor plan substructure

5. To minimize protruding of the const-

ruction planks, turn the FIX STEP plates.

6. For a terrace length of more than

360 cm, a FIX STEP edge plate must be

placed in the area of the end joint of the

smooth-edge boards.

Max. 50 cm Max. 50 cm

1cm

32 cm

7. Click construction plank (40 × 60 mm)

into the FIX STEP attachment pieces with

the grooves down.

8. For a terrace width of more than

360 cm, the ends of the construction plank

must always be offset to each other. To do

so, connect the ends of the planks with a

FIX STEP connection clip adjusted to

32 cm and screw on to one side. Maintain a

distance of 1 cm between the construction

planks.

→ Cf. floor plan substructure 8

32 cm

15,5 cm1cm

7cm

4x35

9. For free expansion, the ends of the

smooth-edged boards and of the

construction planks must be positioned

in the same place.

1cm

6cm6cm

32 cm

In addition, to ensure free expansion the

FIX STEP connecting clip must be left open

2 cm wide and 1 cm deep for subsequent

installation of the smooth-edged board in

the area of the screw connection. For the

two highest height settings of the FIX STEP

mounts, a dual smooth-edged board can be

used. To do so, mount construction plank

pieces of 8 cm length to the connection clip

with screws.

13 cm

8cm

2cm2cm

2cm

10. Then exactly align all construction

planks on the side where installation of the

boards begins.

11. After installing the construction planks,

check the position of the FIX STEP plates

and adjust them if necessary.

12. Place perforated tape below the

construction planks and screw it onto all

construction planks by means of the FIX

STEP connection clip. The perforated tape

is used for bracing the terrace.

→ Cf. 12

III

x16

4x35

13. To attach the FIX STEP edge clamps,

cut out the construction planks first only on

the side from where the boards are to be

installed, 12 cm away from the edge, 5 mm

deep and 2mm deep.

After that, the two-part FIX STEP edge

clamp is fitted into this groove and to the

construction plank by means of pliers.

→ Cf. 13

5 mm

12 mm

III

14. To prevent subsequent slipping of the

boards, self-adhesive retaining tape must

always be fastened to the construction

plank that is closed to the centre of the

boards.

→ Cf. 14

Installation of the boards

15. The first board is pressed into the

positioned edge clamps. Keep a distance of

2 cm to upright, fixed components. When

using the optional house connection profile,

first insert the board, then position it.

→ Cf. 15

16. First, insert groove strip loosely into

the board groove (do not stretch or tighten).

17. The connected FIX STEP connection

clips are then set onto the each of the

construction planks, pushed under the

groove strip against the board and engaged

by means of pliers.

I II

III

18. If boards are to be fastened at a

distance of about 10 mm to the ends of the

construction planks, it is necessary to

insert groove bridges before the

connection clips are mounted.

19. After installation of three rows of boards,

the deck should be measured so that

parallel installation is ensured. Attention:

Since the FIX STEP connection clips are

only used to secure the boards in vertical

position, they must be fixed to the const-

ruction planks in every third row of boards

after inserting the groove strip by means of

the supplied screws. Repeat procedure

until the last but one board is installed.

20. Then determine the length of the

construction planks and saw them off to

be flush.

21. Then create the groove for the edge

clamp and finish installing the boards.

→ Cf. installation step 13

22. Now cut the front end of the boards in

the area of the edge to length with boards

extending 1.5 cm over the construction

planks and bevel the cutting edge.

23. When using a dual smooth-edged

board, construction planks pieces of 8 cm

must be screwed onto the construction

plank with an assembly clip. In the corners

of the terrace, dual assembly clips are

required to install the smooth-edged plank

to the longitudinal side and the front side.

Also press in the FIX STEP smooth-edged

edge plate DUO, so that the dual assembly

clip can hang freely.

→ Cf. 23

4x35

III

4x35

1,2cm

8cm

Cut smooth-edged boards to length

parallel to the boards; the smooth-edged

board on both ends of the terrace must be

1.2 cm shorter than the construction plank.

6cm

1,2cm

Hold on smooth-edged board and drill to-

gether with the construction plank using ∅

7 mm drill holes.

24. Keep the maximum distance of 6 cm to

the ends and 50 cm between drill holes.

Then re-drill smooth-edged boards with

∅ 10 mm, lower and attach by means of

screw, washer and nut using a distancing

groove of 1 cm to adjust to the terrace

deck.

1cm1,5cm

4cm

1,5cm

Min.

1,5cm

M8x80

25. Cut smooth-edged boards parallel

to the substructure and drill together with

the construction plank with ∅ 7 mm. Re-drill

smooth-edged boards with ∅ 10 mm and

install them.

M8x80

1cm

4cm

1,5cm

Min.

1,5cm

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

Comentários a estes Manuais

Sem comentários

MegaLite Axis Manual do Utilizador Página 9

Comentários a estes Manuais

Manuais e produtos relacionados com Holofotes MegaLite Axis